Grundfos

COMPANY INFORMATION

Grundfos was established in 1945 in Bjerringbro by the late Poul Due Jensen. He gave his company the name of "Bjerringbro Pressestøberi og Maskinfabrik" (Bjerringbro Die-Casting and Machine Factory) and not until 1967, after several changes of names, did the company get its present name.

 

The Poul Due Jensen Foundation was established as a self-governing institution in 1975. Today, the foundation owns about 86 per cent, staff about 2 per cent and the founder's family about 12 per cent of shares in Grundfos Holding A/S. The aim of the foundation is the continued development of the Grundfos Group. The capital and the profits of the foundation are used solely for the aim of the foundation, that, is the profits are to be re-invested in the Grundfos companies. Grundfos Holding A/S is the majority shareholder in all the Grundfos companies. Lars Kolind was the group chairman.

GRUNDFOS CMBE BOOSTER

The CMBE Booster is designed for domestic and commercial water supply, pressure boosting, irrigation and dewatering applications.

The CMBE series is available in both 1x110-120V and 1x200-240V variants and uses energy efficient, permanent magnet motor technology, which provides unmatched reliability, quiet operation, and energy savings.

Thanks to the integrated speed controller, the CMBE keeps a constant pressure in the pipe system. A pressure sensor monitoring discharge pressure will signal to the speed controller to change the motor speed to adapt the performance to the new situation.

Features:

  • Constant pressure via integrated speed control

  • Compact design

  • Robust, stainless steel design

  • Easy installation

  • Low energy consumption

  • Dry-running protection

  • Noise level below 55 dBA and even lower at controlled speed

     

GRUNDFOS CM/CME

The Grundfos CM/CME pump has been created with compactness, flexibility and reliability as its central features. This horizontal multistage close-coupled pump is a compact, reliable and quiet pump designed to work in a variety of applications.

The difference between the CM and the CME pump ranges is the motor. CM pumps are fitted with mains-operated motors, whereas the motors for CME pumps have an integrated frequency converter and PID controller.

A Grundfos engineered mechanical shaft seal has been designed to eliminate industry-wide problems with shaft seals sticking where SIC-SIC seal faces are used.  The solution builds on both the implementation of a rotation stop on the stationary ring and different surface finishing on both the stationary and rotating rings.

The CM and CME pumps are available in cast iron or stainless steel

  • AISI 304/DIN 1.4301 stainless steel for water and non-corrosive liquids

  • AISI 316/DIN 1.4401 stainless steel offers

     

GRUNDFOS JP-A/JP-D/JP-AD

  • The Grundfos JP-A, JP-D and JP-AD are self-priming, single-stage centrifugal pumps that feature an axial suction port and a radial discharge port. The pumps have a built-in ejector with guide vanes for optimum self-priming properties.

  • Jet pumps are available in two material variants.

    Material variant A: Cover plate, motor stool and base plate in one unit. The handle is fitted crosswise. Both elements are made of composite material.

  • Material variant B: Stainless steel cover plate, aluminium motor stool and stainless steel base plate, all separate parts.

  • Applications

  • Built for a long, trouble-free working life, small and handy Grundfos jet pumps are suitable for a wide variety of water supply and transfer duties in home, garden and hobby applications. When used in combination with a pressure control or tank, Grundfos jet pumps are ideal for small water supply systems.

  • Features and Benefits

  • Self-priming

  • Stable operation even if there is air in the liquid

  • Robust design that makes the pump suitable for fixed installation

  • The pump is directly coupled to a special fan-cooled asynchronous Grundfos motor that is adapted to the pump performance

  • Single-phase or three-phase motor

GRUNDFOS MQ

  • Applications

  • The MQ pump is designed for water supply and pressure boosting

  • in private homes

  • in summer houses and weekend cottages

  • on farms

  • in market gardens and other large gardens.

  • The pump is suitable for pumping of potable water and rainwater.

  • Features and benefits

  • All-in-one pressure booster unit

  • Easy to install

  • Easy to operate

  • Self-priming

  • Dry-running protection

  • Low-noise

  • Maintenance-free

GRUNDFOS SCALA2

  • SCALA2 features a built-in sensor, which constantly measures the discharge pressure. If the pressure drops below the desired level, SCALA2 boosts its operation immediately to compensate for the loss of pressure. We call it intelligent pump control and the result is perfect water pressure.

  • Benefits

  • Perfect water pressure: Intelligent pump control adjusts operation automatically

  • Low noise: As quiet as a modern dishwasher (47 dB(A) in typical use)

  • Easy selection: One variant for all domestic boosting needs

  • Easy installation: Compact, all-in-one solution, plug-and-pump

  • Easy to operate: User-friendly control panel

  • Reliable operation: Dry-running protection, anti-cycling

  • Long lifetime: Quality-tested to perfection, maintenance-free

GRUNDFOS ALPHA

The Grundfos ALPHA is designed for circulating liquids in light commercial and residential heating systems. Available in cast-iron pump housings for closed systems or stainless steel housings for open or domestic hot-water systems.

The Grundfos ALPHA is suitable for

  • Systems with constant head requirements

  • Systems with variable head and or flow requirements

  • Fixed speed requirements

     

GRUNDFOS MAGNA3

The MAGNA3 is an innovative member of the Grundfos family of high-quality circulator pumps. The MAGNA3 pumps make up a broad range of small, medium and large circulator pumps fitted with communication equipment and motors with electronic speed control based on permanent magnet (PM) and compact stator motor technology.
 

With the MAGNA3, you can stop worrying about complicated pump settings. Simply install the pump and leave it on the factory setting, AUTOADAPT.  The MAGNA3 will automatically analyze the heating system, find the optimum setting and then continuously adjust its operation to changes in demand. The result is optimum comfort and minimum energy consumption. In addition, MAGNA3 pumps are extremely flexible and reliable, and have low noise levels, long life and no maintenance requirements. They are fitted with IR communication.

GRUNDFOS UP/UPS CIRCULATORS

Grundfos circulators are specifically designed for heating and cooling systems. The wet rotor design ensures quiet maintenance free operation. Our 3-Speed models allow you the ability to adjust the pump speed to fit your specific application.

Applications:

Specifically designed for heating and cooling in residential and commercial applications.

Heating Systems:

  • Boiler/Hydronic heating

  • Ground-source heat pumps

  • Radiant floor heating

  • Hydronic and fan-coil heating


Domestic Hot-Water Systems:

  • Solar water heating

  • Hot-water recirculation

  • Domestic hot-water heating


Cooling Systems:

  • Chilled water pumping

     

GRUNDFOS CIM/CIU

The Grundfos fieldbus concept is the ideal solution for complete control of pumps and pump systems. The Communication Interface Module (CIM) and the Communication Interface Unit (CIU) enable data communication via open and interoperable networks.

The Grundfos CIM/CIU communication interfaces offer ease of installation and commissioning, user-friendliness, and great value for money in the long term. All modules are based on standard functional profiles for easy integration into the network and easy understanding of data points.

The CIM card/module is an add-on module that allows communication with 15-30 HP 3x460V MLE motors (E-pumps) and the new Dedicated Controls for wastewater pumps.

The CIU communication interface unit is for products with a GENIbus interface such as small E-pumps, circulation

pumps and boosters. CIU units have an integrated 24 to 240 VAC/VDC power supply and are prepared for wall-mounting or DIN-rail mounting.

The CIM/CIU interfaces support the following fieldbus standards:

  • LON

  • PROFIBUS DP

  • Modbus RTU

  • SMS/GSM

  • BACnet MS/TP

Copyright © 2019 IC Mega International Group